NanoKopter & Y-UFO kits

The NanoKopter 3x2 frame kit supports 6 motors, with 3 motors are facing up and 3 facing down for increased payload capability. The motors mounts absorb vibration to prevent transmission to the frame and electronics. The aluminum frame includes a servo adjustable camera mount and all fasteners.

1300 Kv motors are not included.

Large image NanoKopter (new window)
3x2 configuration (new window)
Motor and motor mount (new window)
Camera mount (new window)

NanoKopter 3x2 replacement frame arm.

Color

The NanoKopter 4 frame kit supports 4 motors. The motors mounts absorb vibration to prevent transmission to the frame and electronics. The aluminum frame includes a servo adjustable camera mount and all fasteners.

1300Kv motors are not included.

Large image NanoKopter (new window)
Motor and motor mount (new window)
Camera mount (new window)

The NanoKopter 6 (hex) frame kit supports 6 motors. The motors mounts absorb vibration to prevent transmission to the frame and electronics. The aluminum frame includes a servo adjustable camera mount and all fasteners.

1300Kv motors are not included.

Large image NanoKopter (new window)
Motor and motor mount (new window)
Camera mount (new window)

A hover-craft designed with on-board gyros and mixing board that does not require a computer radio. The Y-UFO can be hovered or flown in fast circuits like a helicopter. The Y-UFO utilizes (3) brushless motors mounted on anodized aluminum arms spanning 940mm (almost 1 full meter), and weighing in at 400-grams. Flight times range from 8-15 mins depending on the battery used.

Rev-2 improvements include new 1300Kv motors, speed controller heat syncs for better heat dissipation, and a low battery warning LED.

The base version of the Y-UFO kit is constructed with G-10 and a white plastic canopy, and includes the control/mixing board, (3) brushless HCS 60/2-3e motors, (3) brushless speed controllers, LAGY1 gyro, and HS55 tail servo. Add your receiver and a 3S 1000-2200 mAh 15C battery and go flying.

Upgrade your Y-UFO base kit to a deluxe kit with a carbon canopy, skid supports, electronic holder, servo holder, and upper/lower main plate at a later time.

large image Y-UFO (new window)
Y-UFO electronics (new window)
Y-UFO in flight (new window)
Y-UFO in bank turn (new window)

Y-UFO review on RCgroups
See RCgroups thread on the Y-UFO
Y-UFO video

A hover-craft designed with on-board gyros and mixing board that does not require a computer radio. The Y-UFO can be hovered or flown in fast circuits like a helicopter. The Y-UFO utilizes (3) brushless motors mounted on anodized aluminum arms spanning 940mm (almost 1 full meter), and weighing in at 400-grams. Flight times range from 8-15 mins depending on the battery used.

Rev-2 improvements include new 1300Kv motors, speed controller heat syncs for better heat dissipation, and a low battery warning LED.

The deluxe carbon version of the Y-UFO kit is constructed using carbon for the canopy, skid supports, electronic holder, servo holder, and upper/lower main plates. The Y-UFO kit includes the control/mixing board, (3) brushless HCS 60/2-3e motors, (3) brushless speed controllers, LAGY1 gyro, and HS55 tail servo. Add your receiver and a 3S 1000-2200 mAh 15C battery and go flying.

Y-UFO image (new window)
Y-UFO kit contents (new window)
Y-UFO Deluxe frame (new window)
Y-UFO Deluxe canopy (new window)

Y-UFO Review on RCgroups
See RCgroups thread on the Y-UFO
Y-UFO video